i-m-senior-developer: Command for Claude Code

Archive a completed change in the experimental workflow.

Store selection: If the user names a store (a store is a standalone OpenSpec repo registered on this machine) or the work lives in one, run openspec store list --json to discover registered store ids, then pass --store <id> on the commands that read or write specs and changes (new change, status, instructions, list, show, validate, archive, doctor, context, schemas, view). Once selected, treat --store <id> as sticky for the rest of the workflow. Every unscoped example of those commands below is shorthand: before running it, append the flag. For example, run openspec status --change "<name>" --json --store "<id>", not the unscoped form shown below. Other commands do not take the flag. Hints printed by commands already carry the flag; keep it on follow-ups. Without a store, commands act on the nearest local openspec/ root.

Project check: These steps expect a project that already uses OpenSpec. Before the first step that writes anything (new change, archive, sync specs, or authoring an artifact file), confirm the project has a root: run openspec list --json (with --store <id> when a store is selected, since the store is then the root) and read root. A root object means the project is set up. "root": null means it is not - there is no openspec/ directory here, and a write such as openspec new change would create one as a side effect. The command also exits non-zero, which is that answer rather than a broken CLI, so read the JSON instead of retrying or working around it.

One "root": null is not about setup: when a status error message starts with Declared in or Invalid store declaration in and names this project's openspec/config.yaml (or config.yml), the project does use OpenSpec through a store it declares, which this machine cannot resolve (the store is not registered, or the store: line is malformed). Do not treat it as uninitialized and skip the branches below: stop before writing and show the user that error's message and fix.

Otherwise, with no root, what happens next depends on how this workflow was reached:

• Auto-selected: you chose this workflow yourself, without the user naming OpenSpec, naming this skill, or running its slash command. Stop using OpenSpec and answer the request normally, as you would with no OpenSpec installed. Do not ask them to set anything up and do not mention OpenSpec setup.
• Explicit OpenSpec request: the user named OpenSpec, named this skill, or ran its slash command. Stop before writing and ask how to proceed: set this project up (openspec init), target a store they already have (--store <id>), or continue without OpenSpec for this request. Wait for their answer.

In both branches, never create the root as a side effect: do not run openspec init until the user asks for it, do not hand-create openspec/ files, and do not let a command create it.

<capability-path> is the spec directory relative to specs/ (for example, user-auth or identity/user-auth). Preserve the full path from each delta spec when resolving its main spec.

Input: Optionally specify a change name after /opsx:archive (e.g., /opsx:archive add-auth). If omitted, check if it can be inferred from conversation context. If vague or ambiguous you MUST prompt for available changes.

Steps

1. Select the change

   If a name is provided, use it. Otherwise:

   • Infer from conversation context if the user mentioned a change
   • Auto-select if only one active change exists
   • If ambiguous, run openspec list --json to get available changes and ask the user to select one

   When prompting, show only active changes (not already archived). Include the schema used for each change if available.

   Always announce: "Using change: " and how to override (e.g., /opsx:archive <other>).

   Load current archive inputs before the existing archive checks:

   After resolving the selected change and planning root, run:

   openspec instructions archive --change "<name>" --json
   

   Keep the same selected-root flags on this command. This lookup is advisory and optional: it only supplies extra prompt inputs, so it must never block archiving. If it exits non-zero or returns invalid JSON — for example on an older CLI that does not support this command yet — continue the archive workflow with no context and no operation guidance. Do not report an error and do not stop.