This skill should be used when the user asks to configure or troubleshoot AAA (Authentication / Authorization / Accounting) on Huawei S / CE / USG series devices — including 802.1X, MAC authentication, Portal authentication, RADIUS, HWTACACS (TACACS+), local authentication, authentication profiles, free-rule, NAC…
This skill should be used when the user asks to configure or troubleshoot Huawei USG6000E firewall attack defense features. Covers Anti-DDoS (SYN/UDP/HTTP flood), single-packet attack defense, URPF source-address validation, per-IP connection rate limiting, traffic-based dynamic CAR, and SACG admission control…
A guide to configuring BGP, a routing protocol that exchanges network paths between routers, on supported Huawei devices. It covers EBGP between different networks and IBGP within one network.
This skill should be used when the user asks to configure or troubleshoot Huawei USG6000E firewall hot-standby (HRP/VGMP/VRRP) dual-system backup. Covers active/standby, load-balancing, layer-2 transparent, mirror-mode, and virtual-system HA scenarios. Applicable platforms USG6000E V600R007C20+ and…
This skill should be used when the user asks to perform a comprehensive health check / inspection on Huawei VRP network devices (routers, switches, firewalls), including version, CPU, memory, interface, routing, log, and environment status. Use when the user says "巡检某台设备", "做个体检", "查一下设备状态", "health check"…
This skill should be used when the user asks to configure or troubleshoot physical interfaces and link aggregation (Eth-Trunk) on Huawei CloudEngine / S series switches. Covers interface attributes (speed, duplex, MTU, jumbo frame, flow control, PoE, error packets), Eth-Trunk in manual and LACP modes, M-LAG/iStack…
This skill should be used when the user asks to configure or troubleshoot IPSec VPN tunnels on Huawei USG6000E series firewalls. Covers IKEv1/IKEv2 negotiation, IPSec SA, pre-shared key and certificate authentication, point-to-point and template mode, smart-link multi-link, NAT traversal, and L2L scenarios. Applicable…
This skill should be used when the user asks to configure or troubleshoot port/flow mirroring on Huawei CloudEngine / S series switches for traffic analysis and packet capture. Covers local port mirror, remote port mirror (RSPAN/Layer-2/Layer-3), local flow mirror, ACL-based mirror, MQC-based mirror, and observe port…
This skill should be used when the user asks to configure, inspect, or troubleshoot NAT on Huawei USG6000E series firewalls. Covers source NAT (NAT-policy / NAPT / Easy-IP), destination NAT (NAT Server), bidirectional NAT, NAT64/NAT46, and CGN scenarios. Applicable platforms USG6000E V600R007C20+ and…
This skill should be used when the user asks to configure or troubleshoot OSPF on Huawei switches (S1720/S2700/S5700/S6720 V200R011C10+ and CloudEngine 5800-9800 V200R022C00+) or USG firewalls. Covers multi-area OSPF, VLANIF-based OSPF on switches, DR/BDR election, Stub/NSSA areas, route import, route summarization…
This skill should be used when the user asks to configure, inspect, or troubleshoot security policies on Huawei USG6000E series firewalls (USG6300E/6500E/6600E/6680E/6712E/6716E). Covers rule creation (source/destination zone, address, service, application, user), default action, policy groups, logging, content…
This skill should be used when the user asks to configure or troubleshoot Huawei USG SSL VPN for mobile/remote workers. Covers virtual gateway, network extension (full tunnel), web proxy, file sharing, port forwarding, authentication (local/AD/LDAP/RADIUS), and SecoClient deployment. Applicable platforms USG6000E…
This skill should be used when the user asks to configure or troubleshoot Huawei S-series switch stacking (iStack). Covers stack establishment via stack-port or service-port mode, master/slave/standby election, member join/leave, dual-active detection (DAD/MAD), stack split & merge, in-service upgrade, and stack…
This skill should be used when the user asks to configure or troubleshoot static routes on Huawei CloudEngine / S series switches. Covers IPv4/IPv6 static route, default route, route preference, recursive routing, BFD/NQA linkage for fast failover, floating static route, and permanent advertisement. Applicable…
This skill should be used when the user asks to configure or troubleshoot VLANs on Huawei CloudEngine / S series switches. Covers VLAN creation, access/trunk/hybrid port modes, VLANIF Layer-3 inter-VLAN routing, voice VLAN, management VLAN, VLAN isolation (Layer-2/3), and VLAN tag manipulation. Applicable platforms…
This skill should be used when the user asks to configure or troubleshoot VRRP (Virtual Router Redundancy Protocol) on Huawei CloudEngine / S series switches as gateway redundancy. Covers VRRPv2 (IPv4) / VRRPv3 (IPv4/IPv6), backup group, priority, preempt, track interface/BFD/NQA linkage, virtual IP ping, management…
This skill should be used when the user asks to configure or troubleshoot Huawei AirEngine series APs and AC (Access Controller) WLAN networks. Covers AP onboarding (FIT/FAT/CAPWAP tunnel), SSID/VAP, security (WPA2/WPA3, 802.1X, ACL), roaming (intra-AC/inter-AC), RF management (SmartRadio auto channel/power), spectrum…